Skip to content
Buy now, pay later with Klarna.
Buy now, pay later with Klarna.

Iflight Chimera7 Pro HI) BNF DJI air unit 6S (TBS) 1250KV

Original price $907.99 - Original price $907.99
Original price
$907.99
$907.99 - $907.99
Current price $907.99
  • NO RX (DJI BNF)                                                                                     Introducing what has been requested for too long already! A super-efficient iFlight 7inch Long-Range bird that can go where you couldn't go before and can carry bigger batteries to get the flight time to surf the swiss alps if you want! A super stiff frame for minimum resonance and XING2 2809 motors for maximum 7inch prop control. Fly big batteries top-mounted, or even bigger batteries bottom-mounted, 6cells recommended or 5cells for slow cruising. But whatever style you fly, a Lipo or Lion pack will just do the job. Recommended 5S 3.000mAh above (slow cruising) or 6S 2.500mAh above. 
  • GPS functionality to find your way back and Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behavior; Setup instructions included). Vertical and horizontal TBS Crossfire antenna mounts are included to cover you and your antenna dead-ends just in case. GoPro universal TPU bottom stand included; fits your original GoPro bracket and our TPU GoPro protectors (additional).

Main Changelog from Chimera7 to Chimera7 Pro:

  • SucceX-D F7 V2.2 Stack (F7+50A ESC) upgraded to BLITZ F722 Stack (F7 V1.1 + 55A 4in1 ESC)
  • New Lightweight Side Panels Design - Keep Your Rig Clean
  • XING 2806.5 upgraded to XING2 2809 1250KV
  • 7-inch frame upgraded to 7.5inch

HIGHLIGHTS:

  • Battery voltage LED status light (illuminated IF logo on the bottom)
  • 360° TPU protection, DJI cam protection and antenna mounts
  • GoPro TPU bottom stand (GoPro protector not included)
  • Lightweight Side Panels Design - Keep Your Rig Clean
  • No props in view (DJI Air unit record in 1080p/60fps)
  • XING2 2809 1250KV efficient wide stator motors
  • GPS pre-installed for more safety at a distance
  • 6mm rigid arm design for more stiffness
  • Top- and bottom battery mount option

PRE-TUNED & PRE-SETUP:

  • Is this your first BNF or are you just starting through with FPV? This article might probably help: General Guide // iFlight BNF
  • Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!
  • To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"
  • Angle-Mode (self-balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!
  • Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode"
  • GPS Rescue is OFF by default to prevent unwanted or unexpected drone behavior.
  • Please check our linked article on"GPS Rescue Mode // Setup"

Specifications:

  • Weight: 695g (without battery and GoPro mount)
  • Total Dimensions: 258*200mm (body dimension)
  • Bottom to Top Distance: 20-29mm
  • Arm Thickness: 6mm
  • Upper(middle) Plate Thickness: 3mm
  • Bottom Plate Thickness: 3mm
  • Camera Plate Thickness: 3mm
  • Top Plate Thickness: 2mm
  • Geometry:  DC (DeadCat)
  • HQ 7.5X3.7X3 Propellers
  • XING2 2809 1250KV
  • FC // BLITZ F722
  • ESC // BLITZ E55 4-IN-1 2-6S ESC

ELECTRONICS // BLITZ F7 Stack (F7 V1.1 + 55A 4in1 ESC):

BLITZ F722 Flight Controller

  • Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter
  • Smartaudio / IRC Tramp VTX protocol supported
  • Firmware target: IFLIGHT_BLITZ_F722
  • Motor outputs: 4x (SH1.0 connector)
  • Flash: 32MB (Blackbox flash)
  • I2C serial: SDA / SLA pads
  • Dimensions: 36.5*35 mm
  • Barometer: DPS310
  • OSD Chip: AT7456E
  • LED controller: Yes
  • MCU: STM32 F722
  • Beeper pad: Yes
  • Gyro: BMI270
  • Weight: 7.8g
  • UARTS: 6

ESC // BLITZ E55 4-IN-1 2-6S 55A ESC

  • Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
  • Mounting Holes: 30.5*30.5mm/Φ4mm
  • Target:   IFLIGHT_BLITZ_G2
  • Supports 2-6S Lipo input
  • Current sensor: Yes
  • Constant: 55 Amps 
  • Current rate: 200
  • Burst: 65 Amps
  • Weight: 15.3g
  • MCU: G071
  • BEC: No

Chimera7 Pro HD BNF Included Components and Parts

  • 4 x HQ 7.5X3.7X3 CW propeller + 4 x  HQ 7.5X3.7X3 CCW (Color may vary)
  • 2 x Albatross LHCP 5.8GHz SMA FPV Antenna
  • 2 x iFlight Lipo Strap 20*250mm (Black)
  • 1 x Pre-built and Tested Chimera7 Pro
  • 1 x DJI FPV Air Unit Module + Camera


Note:

  • All iFlight BNFs are tested before shipment to guarantee the highest quality. 
  • If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.
  • iFlight takes no responsibility for issues with DJI or Caddx 3rd party gear (Video transmitters, Goggles, Radios, etc) and must be directly reported to www.caddxfpv.com/pages/contact-us or www.dji.com